|
|
|
Panov E.I., Polischuk V.Y., Khanin V.P. THE IMPROVEMENT OF THE TENSION OF THE WOOD SAWDUST INTO THE EXTRUSION AREA OF THE PELLET-MILL WITH THE CIRCULAR DIEPellet-mills are widely used in the production of pellets from raw materials of vegetable origin. Starting from the 20-ies of the last century they were used for pressing feed, and lately they are used for pressing of wood sawdust. Because of this there are the problem of the optimal design of such working elements of the pellet-mills. The solution lies in to conduct identification and verification of mathematical models of the extrusion process in semi-pressing into the working elements of the pellet-mill. For one of the same models which describes the stress of the extruded semi-finished product on the contact surfaces of working elements: the circular die and the pressing roller, such a procedure was performed. Based on the results of the experimental determination of the normal to the surface of the pressing pellet-mill roller extrusion tension softwood sawdust with the humidity of 10% and identification of a mathematical model of the tension state of the semimanufactured material in the areas of the lag and lead wedge workspace of the pellet-mill was refined theoretical description of the tension state in the area of semi-finished extruded — distribution extrusion area normal tension and shear tension on the contact surfaces of the die and the press roller between which there is a differential dependence.Key words: The Reliability of the results was proved by the high value of the confidence factor of the approximation. This result allows to specify the force which are operating under the working elements of the pekket-mill with the circular die, and therefore to refine the calculations of strength and durability of the pressing mechanism.
References:
1. Gomonay M.V. Production of fuel briquettes. Wood raw materials, equipment, technologies, operating modes: monograph. — M: Public GOU VPO MGUL, 2006. — 68 p.
2. Kuchinskas Z.M., Osobov V. I., Freger Yu.M. The equipment for drying, granulation and briquetting of the feeds. — M: Agropromizdat, 1988. — 207 p.
3. Nazarov Century. And., Bulatov I. A., Makarenko D. A. Features of the development process, extrusion granulation biofuels from wood and plant waste // Chemical and petroleum engineering. 2009. No. 2. S. 35 — 39.
4. Didenko C. N., Carpenters D. A. Pellets — wood granular fuel. How to reduce the cost? International scientific journal "Alternative energy and ecology", 2007, №8
5. Golovkov, S. I., Caperin of the Imperial family, Naydenov Century. And.,the Energy use of wood waste. — M.: Forest industry, 1987. — 10-33 C.
6. Unksov E.P. Engineering theory of plasticity. — M: Mashgiz, 1959. — 328 p.
7. Kartashov L.P., Polischuk V.Y. System-defined synthesis the technological objects APK. Ekaterinburg: UB RAS, 1998. — 185 p.
8. Polischuk V. Y. Determination of necessary pressure of a squeezing of a material through the die channel.//Modernization existing and development of new types of the equipment for the food industry. — M: MGUPP, 1977. — P. 113-122.
9. Stress condition of the half-finished food between the working elements of the press-granulator / E.I. Panov, V.Y. Polischuk, V.P. Khanin, N.P. Fefelov, Y.V. Medvedeva // Bulletin SamGUPS. — 2013. — №2(20). P. 32-37.
10. Software ZETLab. Operator manual. Part 1. ЗТМС.00068-01 34, edition 2nd — 385 p.
About this article
Authors: Hanin V.P., Polishchuk V.Yu., Panov E.I.
Year: 2015
|
|
Editor-in-chief |
Sergey Aleksandrovich MIROSHNIKOV |
|
|